Hi all!
It took a freakishly long time to put something together, worth listening to.
By all means, I am an amateur mandolin player, still running through few basic chords and scales.
What...
Type: Posts; User: Rob590
Hi all!
It took a freakishly long time to put something together, worth listening to.
By all means, I am an amateur mandolin player, still running through few basic chords and scales.
What...
Hi Bill,
yes, I was anxious to put the strings on and play it. Bear in mind that I have never held or played a mandolin before, nor acoustic, nor electric.
After making a compensated bridge out...
Hi all,
just a few notes and pictures of the progress over the last few weeks!
I went with 3 layers of Rustins Danish oil, followed by a coat of wallnut wax. First layer of Danish oil was...
Hi!
Not an expert, but took a deep dive into the electronics and wiring recently. :)
For the tone knob, could be the potentiometer taper (audio vs. linear) or it could be capacitor value.
...
Hello,
I hope you all are safe and well!
As I am still working mostly in evenings, I use limited time to work on my project, rather to take too much pictures. So, I would say, more shop, less...
Thanks for the input.
In the end, I will glue the neck in. Since my glueing surface is a bit smaller compared to yours, should I stick to the D3 type wood glue, or should I use 30 min epoxy glue?...
Hi all!
Still going strong with the build! Unfortunately, time to work on my project is becoming quite a scarce commodity.
I made some small progress by chiseling out the neck pocket. First I...
Hi all!
Work on this little beast is still in progress, but balancing work and family has to take the toll somewhere. :grin:
Again, I managed to snap a few pictures throughout the process. I...
Hi all!
As promissed, this is really a slow build. :)
Over the past few weeks I managed to prepare the body blank. I started with four quartersawn 4/4 cherry boards which I cut to the size and...
Hi all!
A bit of work was done since my last post.
Before pressing in the fretwire, I sanded the fretboard with 180 and then 220 grit sandpaper glued to the piece of float glass, in order to...
Thanks for all the input!
I decided to glue the fretboard first, cut the neck to shape, install the frets and then carve the neck. Since fretwire will be pressed in, leaving the neck uncarved and...
Thanks, that puts things into perspective a bit! :)
I initially wanted to do the dots, but I felt a bit underwhelmed with them in this build. Usually people like to complicate too much in the...
Hi all!
As already announced, this is going to be a looong build. :)
Here is a small update.
The fretboard has been sloted and cut to size. I wanted to do simple square fret markers, but...
Hi guys, thanks for the comments!
@WarrenDev
Yes, you can see the pencil lines correctly, I went for this crescent moon shape, it just looked nice when I was drafting the initial plans.
I...
Hi all!
I managed to do some work today on the neck. I glued in the wings on the headstock and did some work on the headstock veneer. I had a piece of spalted maple (1-1/8 x 1-1/8 x 11-7/8), which...
Thanks for the interest. I have been quite busy with my day job and found some half hour here and there to do some work on the project.
Regarding the electronics, I will have a custom, hand-made...
Hi guys and thanks for your comments!
I made some baby steps, started to square up the fretboard blank. It is quite oversized, I will dimension it as I move along with the planing. Still working...
Hi all,
I hope that all is well!
To briefly introduce, I am Rob and I am about to embark on a journey to build my first solid body 8 string electric mandolin.
I will be quite a daredevil and...