Search:

Type: Posts; User: rcc56

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Re: Why are old Gibson snakeheads worth so much more?

    And the snakeheads were only made from 1923 to 1927 or so. After that, they went back to the paddle head. Those later paddle heads had truss rods and tended to have a slimmer profile than the...
  2. Replies
    3
    Views
    217

    Re: Was just gifted a 1906 mandolin

    Sunburst's post covers just about everything.

    If the pickguard is not inlaid into the top, the mandolin was made a bit later than 1906, which is not a bad thing. The serial number, if readable,...
  3. Re: Why are old Gibson snakeheads worth so much more?

    I've had quite a few oval hole Gibson A models in my hands.
    My experience is that their tonal characteristics can vary considerably from instrument to instrument, but I have not found any...
  4. Re: Lost in my search of a mandolin for classical music

    Good luck on the L & H style B. They are very fine instruments, and remarkably consistent in quality.
    And if you ever do any performing, they will eat up a microphone.
    The one you're looking at is...
  5. Replies
    9
    Views
    382

    Re: Mandola string advice sought

    I will confirm that the D'addario mandola set is too heavy for old Gibson mandolas.

    I recommend the following set for these old-timers: 12-20-32-49
    Loop end singles are available from D'Addario...
  6. Replies
    10
    Views
    464

    Re: question on restoring an old gibson

    John gave you some good info in his first post.
    It would probably be necessary to at least remove the part of the fingerboard that covers the top.

    I also agree that the instrument has already...
  7. Re: Lost in my search of a mandolin for classical music

    Mandolins with "canted" tops [tops with a crease adjacent to the bridge] tend to have a sound that might be considered to be "traditionally suitable" for the classical repertoire. Good choices would...
  8. Replies
    9
    Views
    382

    Re: Mandola string advice sought

    I make up my own sets from singles-- 12-20-32-49.
    It's a good set for the old Gibson oval hole mandolas.
  9. Replies
    10
    Views
    303

    Re: Will CA Help on These Stradolin Cracks?

    Bill, thanks for considering me. And Mike, thanks for the referral.
    For the record, I'm in the Chattanooga area, not Nashville.
  10. Replies
    10
    Views
    303

    Re: Will CA Help on These Stradolin Cracks?

    The use of CA will make a correct repair impossible.
  11. Replies
    28
    Views
    1,390

    Re: Purchasing a good beginner mandolin in Canada

    Folkway Music in Waterloo, ON-- www.folkwaymusic.com has a dozen mandolins in stock, including several Eastman models, amy of which would be a good choice for a first mandolin. A model 505 would...
  12. Replies
    46
    Views
    1,733

    Re: Tell me why not: Carbon fiber bracing.

    All I know about it is that a friend of mine who has built a few instruments built a guitar with laminated CF/spruce bracings.
    A couple of the braces eventually split, and he said he would not build...
  13. Replies
    11
    Views
    597

    Re: Gibson F-5 neck on Ebay

    For the benefit of future viewers in case the julienslive link expires, the match for Jim's example is a Gibson F-12, serial number 964724, made sometime during the 1970's.

    Both necks have the...
  14. Replies
    20
    Views
    1,318

    Re: 2nd Mandolin. Ellis? Gibson? Clark? Weber?

    You can pretty much knock Gibson off your list unless you decide to buy an antique one. Except for a short run of flat top Army-Navy reissues and a very small number of custom order modern...
  15. Replies
    27
    Views
    753

    Re: Neck heel crack repair on beater mandolin?

    This is an example of what Don Teeter, who wrote one of the first good books on guitar repair [required reading], referred to as a Q & D repair. Quick and dirty.
    I only use such techniques for...
  16. Replies
    26
    Views
    2,277

    Re: Waxing the mandolin

    Disclaimer: "Paste wax may be hazardous to your finish's health. Wax at your own risk."
  17. Replies
    27
    Views
    753

    Re: Neck heel crack repair on beater mandolin?

    I agree with your wife.

    If I was going to try glue, I would not use CA. I would flex the joint gently while rubbing Titebond into it, then try to find some way to pull it into position so the...
  18. Replies
    11
    Views
    597

    Re: Gibson F-5 neck on Ebay

    My initial reaction was to say that if it is a Gibson neck, it's a prototype, but . . .

    I did a little digging. Checked Gruhn's Guide, and they noted that F-12's made from 1970 to 1980 had a...
  19. Replies
    8
    Views
    376

    Re: Washburn Bowl back neck re-set

    You can use a 1" x 5" 25 watt heat blanket, available from McMaster-Carr or MSC Industrial to lift a mandolin fingerboard. You can use the same heat blanket to lift flat top guitar bridges. A...
  20. Replies
    8
    Views
    376

    Re: Washburn Bowl back neck re-set

    I haven't done one exactly like this, but . . .

    1. Rather than using the guitar oriented techniques such as removing material at the bottom of the heel, you might instead consider installing a...
  21. Replies
    7
    Views
    558

    Re: What, when, where?

    You could call them antique.
    Interesting looking instrument.

    A digression-- A few years back, one of the Nashville stores had a Gibson J-35 guitar in their showroom that had been owned by a...
  22. Replies
    13
    Views
    420

    Re: Luthier in Central Florida

    Time for some of the younger folks to start learning the craft.
    At 66, I'm not yet retired, but am moving much slower than I used to, and find myself reluctant to get started on jobs that are...
  23. Thread: Finish cracks?

    by rcc56
    Replies
    29
    Views
    1,365

    Re: Finish cracks?

    Most, if not all modern Gibson instruments are sprayed by robots rather than hand-sprayed.
    Depending on how the machines are calibrated on any given day, this can result in very heavy finishes.
  24. Re: lattice or x brace reconstruction on oval hole 1915 Washburn?

    Thin. Perhaps 0.100".
  25. Re: lattice or x brace reconstruction on oval hole 1915 Washburn?

    As a repair and restoration person, I will offer the following suggestions to ensure the structural integrity of the instrument:

    1. Loosen the fingerboard extension between the the soundhole and...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4