Enjoyed that. Thanks!
Type: Posts; User: Rockyjohnstone
Enjoyed that. Thanks!
Well let me say you kept me thinking about. You asked many questions that I asked myself and thought long and hard about what the next best step should be in the evaluation.
I've visited the...
Works only one way, clockwise. Not hearing any noise in the neck like before and not sure what that was all about. the neck will go from flat, to about .006 of relief in the middle of the neck with...
I contacted Saga as suggested and learned this,
"It is a "Traditional Two-Way Adjustable" rod. The nut is not removable as far as I know. I can't tell without looking at it if there is a problem...
I agree, that nut is not meant to be removed. I suspect my lengthy posts have muddied up the water to some degree. My apologies, and you guys have been great in helping me work through this.
To...
Thanks Nevin -For the record, it has a 5/32 allen nut. I read several articles about doing just what you suggested, adding a washer to get more adjustment from the truss rod. Interesting thing...
Thanks John. I appreciate the added detail with the fingerboard extension. I'm relieved to hear I don't have to risk major damage to move on with this project.
Regards.
Pete
In an effort to get a better analysis of the 505 neck problem, I installed some temp shims in the fret slots and strung the instrument up to tension. The one way truss rod does in fact function, has...
Nice work indeed. Your customer must be very pleased for sure.
First off, I appreciate everyone's feedback regarding the KM 505 truss rod concern.
I mentioned in my original post that I could not say for certain that the truss pictured was in fact the same as...
Understood. I do recall sighting down the neck. It looked dead flat on the treble side with the same slight rise on the bass side near the nut I described earlier. Failing to check the TR...
Yet another question regarding the KM-505 refret project. Older model non radiused neck. I acquired this mandolin to learn how the do a full fret. I may have gotten a little more than I bargained...
Well that explains alot, and makes perfect sense. I was wondering about that, and was in fact thinking 35 degrees (down) from horizontal plane of the fingerboard. You did point out perpendicular,...
35 degrees seems to be the norm, I'm not confident I should start with that. While a 45 degree angle is steeper and perhaps not as pleasing to the eye to some, choosing 35 will cut back further onto...
I don't post often, but spend hours reading the "build and repair" forum here. Great Stuff!
I'm doing my first refret. KM-505 bound fingerboard. For the most part, I'm following the pictorial on...
Good answer. Thanks Bryce
Is .002 over string gauge too large? I would tend not too think so, but thought I'd check.
I wouldn't hesitate on a guitar, but these dang mandolins can be fussy.
Been to Fremont a bunch of times and never noticed her shop, (said the blind man). Checked out her website, I'll be callin'.
Thanks Austin.
Need a partial re-fret for my MT. Recommendations? I'm not opposed to waiting or paying a premium for high quality work. Goin' fishin', I'll check back in a week.
Thx
Reading positive feedback on V Picks. Hope to try one soon. Thanks
I bought one used from a cafe member to try out. It arrived today in fact. Blue about 1.5mm, shaped almost identical to a BC TPR, but a bit larger. Sounds like a Bluechip to my ears so far. ...
Dear Santa... Let me know where to forward my address;-
I was at the show at Dusty Strings last night. Outstanding performance... Bravo!
Pete, I spent some time watching your videos of ergonomics of the left hand. Very helpful. In particular, the part about using the natural ability for the index finger to stretch back towards the...
So much to learn about this instrument besides learning to play. Thanks for everyone's input. I'll try the easy suggestions first. Raise the bridge, change to heavier E strings, bridge material,...