Results 1 to 16 of 16

Thread: Narrow nut channel for truss rod

  1. #1

    Default Narrow nut channel for truss rod

    Hello,

    I am trying to get my mandolin set up after the saddle on the bridge broke. It is a Flatiron Festival F5 made by Gibson in 2000 in Nashville. The luthier who is setting it up called me today and said that he was having a hard time getting to the truss rod nut. He said the pocket was too narrow for the tools he has. I asked him if he had on that fit a Gibson and he said he tried, no luck. He said the pocket was so tight he doubted if he could make a socket with enough wall to work. I told him I will search out an answer if I could. So here I am. My question is where can I find the appropriate tool and has anyone run into this problem before. The mandolin was made by Gibson in Nashville and I have always been told that they are basically the same as a Gibson F5G, so I was shocked that the truss rod nut pocket was different sized. Any suggestions would be helpful.

    Thank You

  2. #2
    Likes quaint instruments poul hansen's Avatar
    Join Date
    Jun 2020
    Location
    Danmark
    Posts
    725

    Default Re: Narrow nut channel for truss rod

    If you can get the TR nut out, maybe you could use StewMacs TR rescue tool, that contains a drillbit which can drill the wood around the trussrod.

    https://www.stewmac.com/video-and-id...tructions.html
    Kentucky KM-805..........2 Hora M1086 Portuguese II(1 in car)
    Hora M1088 Mandola.....
    Richmond RMA-110..... .Noname Bearclaw
    Pochette Franz Janisch...5 Pocket............Alfredo Privitera pocket
    Puglisi Pocket 1908........Puglisi 1912.......Puglisi 1917
    3 Mandolinetto ..............C.Garozzo
    1 Mandriola...................Cannelo G. Mandriola...Böhm Waldzither 1921
    Johs Møller 1945............Luigi Embergher Studio 1933
    Marma Seashell back......Luigi Embergher 5bis 1909

  3. #3
    Registered User
    Join Date
    Jan 2009
    Location
    S.W. Wisconsin
    Posts
    7,507

    Default Re: Narrow nut channel for truss rod

    I use a nut driver for a narrower socket. It's thinner than a socket. I have ground sockets down thinner for specific tasks tho and that may be an alternative.
    THE WORLD IS A BETTER PLACE JUST FOR YOUR SMILE!

  4. #4
    Registered User j. condino's Avatar
    Join Date
    Nov 2005
    Location
    Asheville, NC
    Posts
    2,758

    Default Re: Narrow nut channel for truss rod

    Find another luthier immediately! This is not a complicated task....
    www.condino.com

    Crafted by hand in a workshop powered by the sun.

  5. The Following 2 Users Say Thank You to j. condino For This Useful Post:


  6. #5
    Registered User sunburst's Avatar
    Join Date
    Nov 2003
    Location
    Kentucky
    Posts
    15,863

    Default Re: Narrow nut channel for truss rod

    A serious pet peeve of mine!
    You decide a truss rod needs to be adjusted, should take a couple of minutes, tops. Instead you spend half a day trying to find a tool to fit the poorly though out and poorly made truss rod situation. Instead of a quick and easy set-up step, you either have to waste the customer's money of loose money just trying to adjust the truss rod.
    We've been over this before on here.
    When I encounter this I remove some wood to make way for a tool to make the adjustment. Some people think that is a horrible thing to do, but if the darned thing was done right in the first place the wood would already be gone so that there would be room to work!

  7. The Following 3 Users Say Thank You to sunburst For This Useful Post:


  8. #6

    Default Re: Narrow nut channel for truss rod

    Might be worth mentioning that the pocket could have been correct, but that the nut can be various diameters, so it’s possible the original one was replaced at some point with a wider one. Even so, if what’s there is one of these long nuts with a cone taper on the outboard side, it should be removable without even getting a socket around it - unless it’s wrong thread, crossthreaded, or corroded. However, someone stymied by the removal issue probably shouldn’t be trusted with the adjustment subsequent.

  9. #7
    Registered User Tom Haywood's Avatar
    Join Date
    Oct 2008
    Location
    PTC GA
    Posts
    1,348

    Default Re: Narrow nut channel for truss rod

    Been there myself. Thin walled socket, thin walled nut driver, Gibson or other truss rod wrench, or whatever you have that works without boogering up the nut. Sometimes nothing will fit, showing that the manufacturer had their own special tool for the job (Gibson!). Sometimes it is not just the shallow depth of the wood around the nut, but also that the pocket is too short to get a straight tool (such as a standard length short socket or nut driver) to the nut. Sometimes the excess rod is too long for for a standard nut wrench to reach the nut. One way or another, there goes your entire fee for a set up. It is a major pet peeve of mine, too.

    Calling the customer about concerns at this point seems completely reasonable to me. In some cases you do have to take out some wood at the most vulnerable place on the mandolin. That is not part of a "standard" set up, and the luthier may feel that full disclosure is in order. Taking out wood or making a new tool requires added time and skill. The luthier may not feel comfortable with that, or he may be indicating that the fee needs to be higher. I recall that some of the Gibson Festival mandolins are very small in the truss rod nut area. If that's true with this one, I wouldn't fault a luthier for being extra cautious or not wanting to do the job at all.
    Tom

    "Feel the wood."
    Luthier Page: Facebook

  10. #8
    Likes quaint instruments poul hansen's Avatar
    Join Date
    Jun 2020
    Location
    Danmark
    Posts
    725

    Default Re: Narrow nut channel for truss rod

    Have you checked if there is an additional allan/hexkey hole in the top of the nut?
    Kentucky KM-805..........2 Hora M1086 Portuguese II(1 in car)
    Hora M1088 Mandola.....
    Richmond RMA-110..... .Noname Bearclaw
    Pochette Franz Janisch...5 Pocket............Alfredo Privitera pocket
    Puglisi Pocket 1908........Puglisi 1912.......Puglisi 1917
    3 Mandolinetto ..............C.Garozzo
    1 Mandriola...................Cannelo G. Mandriola...Böhm Waldzither 1921
    Johs Møller 1945............Luigi Embergher Studio 1933
    Marma Seashell back......Luigi Embergher 5bis 1909

  11. #9

    Default Re: Narrow nut channel for truss rod

    I agree with John, sometimes I have to remove a little wood to get a tool in there. I have a tiny 3mm (approx 1/8") blade chisel that is great for this. It is razor sharp and just "shaves" away the right amount of wood.....also useful for saddle slots, nut slots, inlay work, etc....

  12. #10
    Teacher, repair person
    Join Date
    Oct 2017
    Location
    Southeast Tennessee
    Posts
    4,078

    Default Re: Narrow nut channel for truss rod

    I've seen pockets that were so small that I wondered how the factory ever got the nut on in the first place.

    If a tool can't be found, one can be modified. If that won't work, you've got a problem.

    If you think you have to remove wood, cease and desist, let it sit for a day, then take a second look. If it is necessary to proceed, be extra careful, make sure you have the right tool for the job, make sure it is extra sharp, and take only one stroke at a time.

  13. #11

    Default Re: Narrow nut channel for truss rod

    Right: used to be American assembly workers put in sheet metal screws in cars and appliances by hammering. Carpenters in a boom area where I lived would put heat register cutouts in floors with an axe. How many truss rod nuts an hour coming down the line?
    Anyway, if it’s possibly useful, add a set of cork stopper borers to the kit. These are things you might have seen in high school chemistry class; a nested set of many diameters of thin-wall hollow tubes with inside bevels. Plus the interesting sharpener that comes with them.

  14. #12
    Registered User sunburst's Avatar
    Join Date
    Nov 2003
    Location
    Kentucky
    Posts
    15,863

    Default Re: Narrow nut channel for truss rod

    Quote Originally Posted by rcc56 View Post
    ...pockets that were so small that I wondered how the factory ever got the nut on in the first place...
    Undoubtedly some of them were installed with the nut already threaded on. There is no way it was screwed on there after the thing was assembled. Sometimes it's hard to really care about your factory job, especially when you have to assemble a bad design.

  15. #13
    Teacher, repair person
    Join Date
    Oct 2017
    Location
    Southeast Tennessee
    Posts
    4,078

    Default Re: Narrow nut channel for truss rod

    Oh. It thought it was Murphy's magic manufacturing gremlins that installed those nuts. Those ignominious little devils will work cheap enough to satisfy even a deposed manufacturing mogul like H.J.
    Last edited by rcc56; Mar-03-2021 at 5:22pm.

  16. #14
    Registered User
    Join Date
    Sep 2002
    Location
    DeKalb, IL
    Posts
    3,633

    Default Re: Narrow nut channel for truss rod

    I think John has it. The truss rod nut and washer were put on when it was glued in. I've done it to myself on occasion. So I have learned how to deal with it afterwards. First comes the dope slap on your forehead. Then the curved gouge. Then the ground down nut driver.

  17. The following members say thank you to Dale Ludewig for this post:


  18. #15

    Default Re: Narrow nut channel for truss rod

    Much of this thread reminds me of one a few weeks ago regarding which truss rod is best. The TRMT and similar ones from LMI continue to look very sensible to me.

  19. The following members say thank you to MrMoe for this post:


  20. #16

    Default Re: Narrow nut channel for truss rod

    I just went thru this on an old epiphone, very tight opening for a 7mm nut. I ended up cutting a small amount of wood away from the sides. Just cut a tiny bit away mainly from the overlay. The truss rod cover was still much larger so there was no physical damage. I found that a 12 point 7mm box end wrench did the job just fine.

  21. The following members say thank you to Lbartosh for this post:


Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •